Excavator 360 above 10 tonnes: tracked (experienced)

Last updated: 11 December 2024
Grant rate/tier: £470 (Plant tier 3 experienced)
Grant code: GET3287

Overview

This standard is exclusively for use by Approved Training Organisations (ATOs). The purpose and scope of this standard is to provide the learner with the skills and knowledge to support the operation of a 360 excavator.

Find a course for this standard

Duration

Minimum

14 Hours including assessment time

1 learner. 1 trainer. 1 machine

21 Hours including assessment time

2 learners. 1 trainer 1 machine
3 learners. 1 trainer. 2 machines
4 learners. 1 trainer. 2 machines

Learners must cover all learning outcomes of the standard in full, the trainer must decide and be able to demonstrate and document their decisions for choosing the learners route based on their knowledge and skills through a documented profiling approach. Evidence of the profiling and decisions must be kept and made available on request.

The duration must not be reduced.

Learner pre-requisites

The learner holds a current industry recognised red card within the plant category or has equivalent experience. The trainer must decide and be able to demonstrate a thorough initial assessment and document their decisions for choosing the experienced route based on the learners knowledge and skills through a documented profiling approach

Purpose/scope

The purpose and scope of this standard is to provide the learner with the skills and knowledge to support the following:

operation of a 360 excavator – to carry out basic excavation, loading and grading type work
fit and use a range of bucket types
site the machine safely and efficiently for excavating, grading, and loading duties
carry out checks and minor adjustments and prepare the machine for work
travel the machine within site conditions
understand the capabilities, purposes, and limitations of using the 360 excavator for excavating, loading and grading duties
comply with all safety requirements
interpret given information to carry out excavating, loading and grading duties to given tolerances

Occupational relevance

Training delivered against this standard would be relevant to the following occupational group(s):

operative and craft

Instruction/supervision

As a minimum, course trainers must be able to demonstrate that, in relation to this standard, they have:

Essential:

Either of a/b

Current card issued by one of the CSCS partner plant schemes at instructor/trainer/assessor level bearing the category of 360 excavator
Current card issued by one of the CSCS partner plant schemes at operator level bearing the category of 360 excavator

Level 3 Award in Education and Training or equivalent qualification listed in Appendix 3 of the Requirements for Approved Training Organisations
health and safety qualification at or equivalent to construction site management level, examples of which can be found in Appendix 6 of the Requirements for Approved Training Organisations
In addition to the required qualifications, the trainer must be able to demonstrate operational experience of operating the excavator 360 relating to the training they are delivering. This can be demonstrated with a valid and in date blue card from a ‘Recognised Organisation’ and a minimum of 3 years’ site experience.

Desirable:

S/NVQ Level 2 Plant Operations in the specific category being trained
Level 3 Certificate in Assessing Vocational Achievement

Delivery

Training and assessment may be delivered in an on or off-site environment.

Where training and assessment takes place within a working construction site environment, training must be segregated from productive work within a prescribed training area, which has been risk assessed and has appropriate control measures in place as required by current legislation and regulations.

All equipment required for the training must be set aside specifically for the training session and be available for the entire training duration. Equipment is not to be shared with the working construction site.

Welfare facilities must be provided wherever training and assessment takes place, and this should meet relevant legislation.

All materials and equipment must be of a suitable quality and quantity for learners to achieve learning outcomes delivery and assessment criteria, and must comply with relevant legislation, regulations and industry agreed requirements.

The class size and learner/trainer ratio must allow training to be delivered in a safe manner and enable learners to achieve the learning outcomes.

Practical engagement can include seat time, any associated practical checks of the machine e.g pre-start checks, and observation time.

Irrespective of the number of learners, effective learning must be maintained for all learners. Equal and sufficient practical engagement needs to be considered.

The following training delivery methods may be used in the delivery of this standard:

face to face learning environment (such as a classroom/workshop/site office) for theoretical learning & assessment
on or off the job site environment for practical learning and assessment
simulator for practical training

Note – if a simulator is used, it can only comprise of a total of 20% of overall practical training and not used in any assessment.

Assessment

For the successful completion of training, learners must complete an end of course practical assessment and knowledge test that has a clear pass or fail criteria as set out by the card scheme. The marking criteria must effectively measure every aspect of each learning outcome and additional guidance for training and assessment.

Assessment must adhere to all points on the CITB Requirements for Approved Training Organisations including Appendix 6 which provides further guidance for assessment

Quality assurance

Recognised standard

CITB will gain assurance through the Recognised Organisations’ quality arrangements.

Approved Training Organisations’ will be required to supply confirmation of approval (centre approval and scheme approval) with the related Recognised Organisations’ awarding organisation or body. In most cases this will be an approval certificate provided by the Recognised Organisations’ awarding organisation or body, listing the routes, qualifications, and categories they are approved to deliver. In addition, a copy of the most recent external quality assurance monitoring report will be required, relating to the standard that you wish to be approved for.

This information will be reviewed by CITB’s quality assurance team. Approval will be subject to the required Recognised Organisations’ documentation being supplied by you. As part of the quality assurance checks, CITB may confirm the accuracy of documentation with the issuing organisation.

Please refer to the Requirements for Approved Training Organisations Appendix 6 for further guidance on quality assurance.